brazing metal的例句大全

The Al-Cu eutectic brazing metal is made to braze pure aluminium substrate in vacuum. The diffusion phenomenon of Cu in pure aluminum bar under different brazing temperature and heat preservation time is investigated by means of SEM and EDS.

制备Al-Cu共晶合金钎料，用SEM和EDS研究不同钎焊温度和保温时间条件下，纯铝棒料基体对接真空钎焊接头Cu元素的扩散行为。

互联网摘选

The Influence of Brazing Metal on Residual Stresses in Brazed Joints of Ceramic-metal

钎料对金属/陶瓷钎焊接头残余应力的影响

互联网摘选

From our experimental results, three rules about the design of an active brazing metal are suggested.

最后，作者建议设计钎焊陶瓷的活性金属钎料的三条原则。

互联网摘选

Study of diffusion behavior of element Si in rapid solidifiable and common Al-Si brazing metal

快冷与普通Al-Si钎料中Si的扩散行为研究

互联网摘选

The diffuse speed and depth of Si element in rapid solidification brazing metal are higher than that in as-cast one.

快冷钎料中Si元素在母材中的扩散速度和深度都远高于普通铸态钎料。

互联网摘选

Al-Cu eutectic brazing metal based on the pure aluminium substrate is welded in vacuo.

制备了Al-Cu共晶合金钎料，以纯铝棒料为基体采用对接接头进行了真空钎焊。

互联网摘选

The results indicated that the diffusion behavior of element Si in the matrix is basically the same no matter whether it came from rapid solidifiable or common brazing metal.

实验结果表明，普通钎料和快冷钎料中Si元素在母材基体中的扩散过程基本相同。

互联网摘选

Adaptability of brazing filling metal used for monolayer diamond tools with vacuum furnace brazing

金刚石工具真空钎焊钎料的适应性

互联网摘选

By using this process, the wettability is obviously improved between the hard metal and the liquid state silver brazing flux and copper brazing flux.

采用这种方法可以明显改善硬质合金与液态银钎料和铜钎料的润湿性；

互联网摘选

Aerospace series-Gold base alloy AU-B 40001-Filler metal for brazing-Wire.

航空航天系列.金基合金AU -B40001.钎焊用填充金属. 金属丝.

互联网摘选

The interface structure of the brazing filler metal with Ni after its spreading was observed by backscattered electron images.

采用背散射电子相观察钎料与Ni润湿后的界面组织。

互联网摘选

Active brazer is key to the brazing of ceramic to metal.

陶瓷-金属活性法连接的关键之一是活性钎料。

互联网摘选

The brazing-ability and quality of brazed seam of 6063 aluminum alloy brazed by Al-Si eutectic filler metal and QF flux is discussed by means of test of spread-ability and test of T joint.

本文用平百铺展试验和T型接头试验，研究了6063铝合金采用AI－St钎料和氟化物钎剂（QF钎剂）钎焊时的钎焊性和钎缝质量。

互联网摘选

R& D of Low Temperature Ceramic/ Metal Brazing Alloy

环保型陶瓷/金属低温钎料的研究与开发

互联网摘选

The study of metal arc brazing in argon method for joining thin plates under 0.5 mm

用熔化极氩弧钎焊方法焊接0.5mm以下薄壁件的研究

互联网摘选

Aiming at shortcoming of machining copper band, the method of cladding copper band using metal inert-gas arc brazing was investigated.

针对机械加工制成铜带的不足之处采用MIG钎焊方法堆焊铜带。

互联网摘选